Rudder Port Bearings & Seals

IMPERIAL SIZE RUDDER PORT BEARING TYPE F

Click here to see detailed information about the product

Choose Size

RPB-F-3250-00

Manufacturer

Tides Marine

Product Code

RPB-F

Product Line

PORT

Price $512.44

Description

RPB-F-3250-00 – The Tides Marine RPB Type F Rudder Port Bearing for 3 1/4 Inch Rudder Stock.

is designed to be installed in rudder tubes which have been laminated or welded into a vessel’s hull. The unit consists of a one-piece UHMW housing with a nitrile lip seal. It eliminates metal-to-metal contact and the associated problems of abrasion, electrolysis and corrosion.

It is 100% water tight and eliminates chatter and vibration, resulting in a quieter, smoother operation.

* PLEASE NOTE:
THE -00 MEANS IT IS OUR STANDARD MODEL. IF YOU ARE REPLACING AN EXISTING BEARING, PLEASE CHECK THE SERIAL NUMBER
TO SEE IF YOUR MODEL IS A -00 MODEL. IF IT IS NOT, PLEASE CALL TIDES MARINE AND ORDER THE CORRECT MODEL
YOU CAN CHECK THE SERIAL NUMBER BY CLICKING ON THE SERIAL NUMBER LOOKUP LINK AT THE BOTTOM OF EVERY PAGE
ON THIS WEB SITE.

The Tides Marine RPB Type F unit is designed to be installed in rudder tubes which have been laminated or welded into a vessels hull.

The unit consists of a one-piece UHMW housing with a nitrile lip seal. It eliminates metal-to-metal contact and the associated problems of abrasion and electrolytic corrosion. It is 100% watertight and eliminates chatter and vibration, resulting in a quieter, smoother operation.

Rudder Port Bearings Type F may be ordered online.

 

Tides Marine makes Type F assemblies based upon a combination of rudder stock diameter (.000″) and the rudder tube I.D. When placing your order, please provide both of these dimensions.


RPB Type F Imperial Sizes
Specifications (dimensions in inches)

Rudder Stock OD Bearing OD Retaining Ring Part Number Buy Online
A B
1 1/2 3 250 RPB-F-1500-00 Buy Now
1 3/4 3 1/4 250 RPB-F-1750-00 Buy Now
2 3 1/2 300 RPB-F-2000-00 Buy Now
2 1/2 4 1/2 350 RPB-F-2500-00 Buy Now
2 3/4 4 1/2 375 RPB-F-2750-00 Buy Now
3 4 1/2 400 RPB-F-3000-00 Buy Now
3 1/4 4 3/4 425 RPB-F-3250-00 Buy Now
3 1/2 5 450 RPB-F-3500-01 Buy Now
4 1/2 6 1/2 600 RPB-F-4500-00 Buy Now
4 3/4 6 1/2 590 RPB-F-4750-00 Buy Now

Tide Marine offers many custom sizes and dimensions. Please call for any size or dimension you do not see here.

RPB-F Installation Guide

The following is a description of the installation procedures associated with the RPB Type-F. Installation instructions are included with each unit and should be followed closely.

  1. Prepare the rudder tube for bonding by wiping the inside clean of any dust or construction debris.
  2. Using a medium bodied epoxy or Chockfast®, coat the outside of the bearing unit that will be pressed into the tube.
  3. Lay a bead of marine sealant (such as Lifecaulk or 3-M 101) under the flange.
  4. Insert the unit into the tube.
  5. Temporary support may be required to keep the unit in position. Install rudder or dummy shaft to insure good bearing alignment until cured.

 

NOTE: Before installing the rudder, insert the red installation hat into the lip seal. When rudder is in place, remove, invert and replace it on top of the Type-F unit to keep debris off the lip seal during use.

 

Complete Type-F Installation Guide maybe downloaded HERE

0
YOUR CART
  • No products in the cart.